Houston, Texas is not known for its cold weather but anything more than a few hours below freezing can wreak havoc on your irrigation system because the backflow device, which must be a PVB or an RP within Houston city limits, is installed above ground.
Understand Backflow Winterization
Understanding how to properly winterize your backflow device is something that everything home owner should know so as to avoid costly repair bills or the possibility of contaminating your water supply. This article will walk you through winterizing a PVB device step by step and includes pictures to guide you. It is very easy, takes just a minute or two and all you will need is a small flat-head screwdriver.
A PVB is the most commonly used residential backflow device in the city of Houston.
Let’s start by learning just a little more about the purpose of the backflow device because it is the most important component of your irrigation system. The backflow device is NOT an irrigation “shut-off” though it does turn water off to the irrigation system when closed.
The sole purpose of a backflow device, which is required by state and local code, is to protect your family’s tap water from harmful contaminants present on the lawn. Things like; fertilizers, fungicides, pesticides and animal droppings are present on most all lawns as well as the surrounding areas. These contaminants are pulled into the irrigation system through capillary action as the sprinkler heads finish spraying and return to their retracted positions below the ground.
The backflow device prevents the contaminated water from mixing with the potable water you and your family use daily so it is very important the backflow device is installed up to code, is well maintained and functioning properly at all times.
An isolation valve is in a valve box usually near the meter or at the foot of the backflow as pictured on the left and will be a simple manual valve, usually a ball valve, like the one seen in the image on the right which is in the open position as indicated by the handle being in line with the direction of the pipe.
Winterize a Sprinkler System Through a Backflow Preventer
There is a great deal of misinformation out there as to how to properly winterize your backflow to avoid a frozen backflow preventer. The most common misconception is that you should simply turn the backflow handles off and wrap the device up during the winter or when a hard freeze comes. This actually significantly increases the chances that the backflow will break during a freeze and can lead to many hundreds of dollars in repairs and inspections.
Backflow Preventer Freeze Protection
Winterizing your backflow device properly can save you a great deal of grief and money, and it only takes one or two minutes.
An isolation valve is in a valve box usually near the meter or at the foot of the backflow as pictured on the left and will be a simple manual valve, usually a ball valve, like the one seen in the image on the right which is in the open position as indicated by the handle being in line with the direction of the pipe.
The following procedure is the proper way to winterize your PVB backflow device in the Houston, Texas area. This is an important distinction because codes and installation methods differ greatly from state to state and city to city.
In the northern U.S., for example, your tap is probably in the basement and you most likely have a drain valve and a place to blow your system out with an air compressor. These components were installed specifically for winterizing your sprinkler system in your environment and may not be appropriate in other markets.
Many far northern parts of the country will simply remove the backflow device for the entire winter season while many deeper south parts of the country have much lighter winters and many of our plants will need some water during the winter months.
Before You Can Start PVB Backflow Winterization
Step One is turning off the isolation valve. You may first have to remove some dirt from the valve box. Give it a quarter of a turn so that the handle cuts across the direction of the pipe as seen on the right. This valve is now in the “off” position.
To properly winterize your Houston-area backflow you MUST have an isolation valve. An isolation valve is most commonly a simple PVC ball valve that will be located in a small, round, green valve box near your meter or at the foot of your backflow (often under the dirt, mulch or grass). We often see them mounted at the bottom of the inlet leg of the backflow device which is not ideal as it is subject to freezing which does not help.
Isolation valves are standard components of an irrigation system and are currently state code though many older systems may not have one. If your system does NOT have an isolation valve then leave the backflow on and simply wrap it with insulation, towels, blankets or they even make an insulated weatherproof pouch for backflow devices that many of your local vendors may carry. DO NOT turn the backflow off as this will significantly increase the chances of freeze damage and will usually result in a crack on the inside of the metal PVB body just above the first ball valve.
We repair many PVBs every year that were damaged from home owners, landscapers and even misinformed irrigators turning the backflow off in this manner. Once again; if you do not have an isolation valve then leave the backflow device alone (do NOT turn it off) and simply wrap it up during the freeze. Give your local irrigation professional a call and have an isolation valve installed for proper backflow winterization in the future.
3 Steps to Winterize Your Backflow Preventer
1. Turn Off the Isolation Valve
After locating your isolation valve step one is simply turning it off. Not all systems will have a ball valve as pictured, some will have a gate valve (like the one on your hose bib) but a ball valve is most common.
A ball valve will only turn a quarter of a turn in either direction and is open (or on) when the handle is in line with the flow of the pipe and it is closed (or off) when the handle cuts across the flow of the pipe. If you have a gate valve (the kind of valve that turns your garden hose on and off) then simply turn the valve handle clockwise until it is hand tight.
The test-cocks have a screw in the center of each that keeps the bleeder valve closed. Those screws are closed in the left picture and open in the picture on the right. Step Two: Open with a quarter of a turn to drain water from the PVB.
2. Open the Bleeders
The next step will require a small flat-head screw driver. With screw driver in hand, standing in front of your PVB we are going to focus on the test-cocks. The test-cocks are a pair of small nozzles that are used to test or drain the main cavity of the backflow. Each of these test-cocks will have a small screw in the center (see picture).
Those screws, as with the ball valve, are open when the slot of the screw is in line with the flow of the metal fitting they are attached to and are closed when the slot cuts across it. Use your screw driver to turn each of the test-cocks one quarter of a turn so that they are open.
Don’t be alarmed by water that may shoot out of the test cock with some pressure, it will quickly die down. This allows the water inside the backflow to drain from the unit.
DO NOT turn the screws more than a quarter of a turn or remove the screws from the test-cocks. When the water draining from the device subsides, give the device a few light shakes to get a little more water out of the device.
You just created an empty cavity in the device so when the water left inside the PVC legs freezes and expands, it has a place to go so it will not fracture the the device or the pipes.
Step Three: First turn one ball valve to a forty-five degree angle and then turn the second ball valve to a forty-five degree angle so that your backflow looks like the one in the image on the lower right corner.
3. Handles at Forty-Five Degrees
Once the draining water begins to slow we can finish the winterization process. Leaving the test-cocks open to drain we are simply going to turn each of the ball valve handles on the backflow device to a forty-five degree angle (meaning that the ball valve itself is half open/half closed inside of the unit). There will be one ball valve at the bottom of the backflow and one ball on the side of the backflow. It does not matter which ball valve handle you turn first.
That’s it!! You have now properly winterized your PVB. If you do not plan on watering your landscape during the winter you can leave your backflow winterized until the temperatures start to climb. If you do water during the winter then you will perform this winterization process before each freeze.
It is always best to consult your personal landscaper, horticulturist, or Houston irrigation systems expert to find out what the winter water requirements are for your landscape before making this decision.
Turning Your Backflow Preventer Back On
To make your sprinkler system functional again you simply need to:
- Open the isolation valve (this is going to shoot water out of the test-cocks but that is okay, we want to let any air or debris in the line escape.
- Close the test-cocks with a screw driver (screw slots vertical) which will stop the water from spraying out of the backflow.
- Return both ball valves to the full open position (handles in line with the flow of the pipe).
Your PVB will once again look like the one in the image featured at the very top of this article.
Contact Us for Help Winterizing Your Backflow Preventer in Houston
As always, Silversand Services is here to help if you need any advice or help in the backflow winterization of your system or if you have a frozen backflow preventer then please don’t hesitate to contact our commercial landscaping company in Houston today! We also provide Dallas commercial landscaping, so consider us for your commercial irrigation services in Dallas too.
